Cart 0
11 FORD F-250 SD 6.2L ECU ECM ENGINE CONTROL COMPUTER BC3A-12A650-CHK TESTED
11 FORD F-250 SD 6.2L ECU ECM ENGINE CONTROL COMPUTER BC3A-12A650-CHK TESTED
11 FORD F-250 SD 6.2L ECU ECM ENGINE CONTROL COMPUTER BC3A-12A650-CHK TESTED
11 FORD F-250 SD 6.2L ECU ECM ENGINE CONTROL COMPUTER BC3A-12A650-CHK TESTED
11 FORD F-250 SD 6.2L ECU ECM ENGINE CONTROL COMPUTER BC3A-12A650-CHK TESTED
11 FORD F-250 SD 6.2L ECU ECM ENGINE CONTROL COMPUTER BC3A-12A650-CHK TESTED
11 FORD F-250 SD 6.2L ECU ECM ENGINE CONTROL COMPUTER BC3A-12A650-CHK TESTED
11 FORD F-250 SD 6.2L ECU ECM ENGINE CONTROL COMPUTER BC3A-12A650-CHK TESTED
11 FORD F-250 SD 6.2L ECU ECM ENGINE CONTROL COMPUTER BC3A-12A650-CHK TESTED
11 FORD F-250 SD 6.2L ECU ECM ENGINE CONTROL COMPUTER BC3A-12A650-CHK TESTED
11 FORD F-250 SD 6.2L ECU ECM ENGINE CONTROL COMPUTER BC3A-12A650-CHK TESTED

11 FORD F-250 SD 6.2L ECU ECM ENGINE CONTROL COMPUTER BC3A-12A650-CHK TESTED

Product Description

Part Number

BL3A-12A650-AEG Match this please! NOTE: One Mounting point is missing but the other should hold this unit in place. Review pictures prior to purchase and do not purchase if you are uncomfortable with this.

Fitment/Interchange

This ecu will interchange or replace the following ecu part numbers for 2011 F-Series 6.2L trucks:

BC3A-12A650-CGK
BC3A-12A650-CHF
BC3A-12A650-CGH
BC3A-12A650-CHG
BC3A-12A650-CHH
BC3A-12A650-CHK
BC3A-12A650-CJK
BC3A-12A650-CKK
BC3A-12A650-EEC
BC3A-12A650-EED
BC3A-12A650-EFC
BC3A-12A650-EFT
BC3A-12A650-EFD
BC3A-12A650-EGD
BC3A-12A650-EHD

Tech Notes

    ECU has been tested with our state of the art vehicle simulator which tests over 25 circuits of the ECU! Some of those are listed below:
  • ECU Starter motor control
  • ECU Purge Control
  • ECU O2 heaters
  • ECU powered up and has communication
  • ECU Shift Solenoids
  • ECU VCT Controls
  • ECU A/C Clutch
  • ECU injectors/coils tested good and much more!

Install Notes

  • Disconnect the negative terminal of the battery. Make sure the battery connector is not touching the battery post.
  • Disconnect and remove the module to be replaced.
  • Install and connect the replacement module.
  • Connect the negative terminal of the battery.
  • See "Programming / PATS Security" below for additional install instructions.

Programming / PATS Security

For Plug and Play you must do the following three steps:

Step 1: Match your part number per above fitment/interchange notes

Step 2: Program ecu to your VIN. You will need your local mechanic, Ford dealer or properly equipped locksmith to program your VIN into the ecu. Without this you will get a "no start" condition. 

Step 3: If your vehicle has PATS security (Most Ford/Lincoln/Mercury's do) you must have your keys programmed. We recommend you have this done by your local locksmith. In most cases they will travel to your location and the process takes less than 30 minutes. No towing necessary and your local locksmith will be cheaper than a dealer. If your vehicle has PATS and is not programmed you will get a "no start".

Item Condition

  • NOTE: One Mounting point is missing but the other should hold this unit in place. Review pictures prior to purchase and do not purchase if you are uncomfortable with this.
  • Pins perfect, none are broken or bent
  • Lock tabs in place
  • Connector plastic may have minor chip but pins, guides and lock tabs are in place.

Warranty

This ECM comes with a 90 day warranty from the date of purchase. Please keep a copy of your purchase record which we will send with your item.